Short answer: Published U.S. rates for CNC machining run from about $35 to $120 per hour for 3-axis milling and from about $75 to $250 or more for 5-axis, and the sources disagree with each other by wide margins. The hourly rate matters less than setup and cycle time, which is why two shops at the same rate can quote very different totals.
Updated November 11, 2026. Rates below are published figures from the sources named, not Machine Tool Search measurements.
How much does CNC machining cost per hour?
There is no single answer, and the published ranges show it. Three recent U.S. pricing guides give these shop-rate ranges:
| Source | 3-axis mill | 5-axis mill |
|---|---|---|
| Fabcon, 2026 US pricing guide | $80–$120 per hour | $150–$250 per hour |
| RapidDirect, CNC milling cost guide | $35–$120 per hour | $75–$250+ per hour |
| Boyi Prototyping, U.S. rates (June 2025) | $40–$80 standard; $80–$120 high precision | $150–$200 general purpose; $200–$300 high-speed or aerospace quality |
These are quoted shop rates, not final part prices. Ranges are as published by each source.
Why do published shop rates disagree so much?
A shop rate bundles the machine, the operator, overhead and profit, so it moves with everything a shop carries. One shop-rate guide notes that location, material prices and equipment mix can shift U.S. rates by 10 to 20 percent (Boyi). A machining-industry writer quoted by MSC Direct says a typical rate is about $150 an hour for a machine that costs $100,000, while some job shops charge only $30 or $35 an hour without accounting for the machine's replacement cost (MSC Direct). Low published numbers often leave something out.
How do shops turn an hourly rate into a part price?
Most shops build a job price from setup, machine time, material, tooling and overhead:
(Setup time × shop rate) + (cycle time × quantity × shop rate) + material + tooling + overhead and margin
Fabcon puts typical setup charges at $50 to $150, with programming at $50 to $120 per hour for one to four hours (Fabcon). Here is an illustrative example using our own arithmetic, not a quote:
| Item (25 small aluminum parts) | Assumption | Cost |
|---|---|---|
| Setup | 2 hours at $75 | $150 |
| Machine time | 6 minutes each, 25 parts, at $75 per hour | $188 |
| Material | Assumed | $90 |
| Inspection and overhead | Assumed | $75 |
| Total | $503, about $20 per part |
Illustrative only. Change any assumption and the total changes.
Why does setup time matter more than the hourly rate?
On short runs, setup is spread across few parts, so the effective cost per part rises even when the hourly rate is low. That is why comparing shops by rate alone misleads. A shop at a higher rate that needs fewer setups, such as a 5-axis machine that finishes a part in one clamping, can come out cheaper per part. Tighter tolerances add slower cycles, more inspection and more scrap risk, so ask each shop to break out setup, cycle time and inspection when you compare quotes.
How is a shop rate calculated?
Shops add the machine's hourly cost to labor and overhead per hour and multiply by a markup, in the general form (machine cost per hour + labor and overhead per hour) × markup (MIE Solutions). The machine cost per hour comes from depreciation or payments, power and maintenance, divided by the hours the machine really runs.
What does the shop rate mean if you own the machine?
The rate a shop can charge depends on what its machines can do, which is also what moves a machine's resale value. If you are weighing a sale, check where similar machines were last listed on our market price pages and see vertical machining centers listed now. To get a number for your own machine, request a free valuation.
Own the machine doing this work?
Tell us the model, year and hours and we will show where it sits against current listings.
Get a free valuationFrequently asked questions
Is CNC machining charged hourly?
Shops use hourly rates internally, but they usually quote per job or per part. The rate is one input alongside setup, material, tooling and overhead.
Why do two CNC quotes differ so much?
Usually because of different assumptions about setup time, tooling and risk, not only different hourly rates.
Is 5-axis machining always more expensive?
Per hour, yes. Per part it can be cheaper, because it can remove several setups that a 3-axis job would need.
What is a typical CNC shop rate in the U.S.?
Published ranges run from about $35 to $120 per hour for 3-axis milling and about $75 to $250 or more for 5-axis, depending on the source, so compare quotes on total job cost.